Lathe Hack and old school tool use.

[Worth1]

Here is the deal on the motor.
It has two capacitors one is a start and the other is run.
It is 3 HP, no motor has a set of start winding that are more powerful that the run winding.
If is the other way around the run winding is less powerful and all it does is bump the motor out of phase so to speak to get it spinning then shuts off by way of a switch after the rpm's get to a certain speed.
I also bet the motor will run off 220 if wired the right way.
If you are serious about using the saw get the Incra miter and fence set up.

Worth

[Worth1]

Got one side welded up last night.
The other side very close to being ready.
Several time I caught myself going to the grinder only to stop myself and say no idiot use your files.
The phrase getter done and I dont go together.
To me it represents poor workmanship and slop, seen it too many times.

Worth

[Worth1]

Here it is almost completed and it slides up and down the ways like no tomorrow and no wobble or any alignment problems.
Just a few spot I need to fill and some contour grinding.
I might just leave the welds as they are on the top and not grind them, nothing I cant do later.

Yep welding in sandals.
20160905_170741.jpg

One of the ugly welds.
20160905_172402.jpg

Personal protective equipment for the lathe.
Tig welders dont throw sparks but if something goes wrong they will.
It would kill me to get one stuck to the ways.

20160904_234250.jpg

[dmforcier]

Nice fill.

These look like they slide free on horizontal ways. What about when the thing is set vertical, as in drill press mode?

[Worth1]

Originally Posted by dmforcier

Nice fill.

These look like they slide free on horizontal ways. What about when the thing is set vertical, as in drill press mode?

The thing isn't complete yet this was just the hardest part.

The bottom with have a flat plat with two more of these half rounds welded to it.
It will have a stud coming up through the one I just made in the center.
On top of the one I just did will have another steel plate with a long slot.
the stud will go through it and there will be a locking handle.

On that top plate will be where the tool rest is attached.

Sort of like in this picture of an old Yates American lathe from the late 30's where I got the idea from.

[Worth1]

Here is one of my metal yards on someone else's place the guy on the front end loader is my neighbor ladies son and his place.
We hauled it all off for free from a woman that was mad at her X husband.

Took two big trucks and two days to get it all.

Plus I have a big stack of stuff on my place.

Worth

IMG_0014.JPG

IMG_0015.JPG

IMG_0016.JPG

IMG_0017.JPG

[Worth1]

I'm at a stand still I have the bottom clamping device completed but I cant make my mind up how I want to join them together.

Worth

[dmforcier]

As per picture, single central stud with wing nut or lever?

[Worth1]

Originally Posted by dmforcier

As per picture, single central stud with wing nut or lever?

Just got through making the stud.
It is 1/2 fine thread NOT "all" thread, it is a stud.
It will be threaded in the bottom plate with nuts on top and bottom to lock in it place.
The top part of the stud is also fine thread where the locking handle will be.
I did it this way so I could index where I wanted the handle to lock at.

I will go to the old school auto store tomorrow to get the nuts it isn't worth my time to make a 25 cent nut.

I like fine threads because it requires less force/torque to get the same amount of pressure against two pieces and they are less likely to come loose.
The stud was threaded long on top so I could just cut off what I dont need.


Worth

[dmforcier]

Okay, I don't get it. Why attach to the bottom plate at all? I guess I'll have to wait and see what you do.

Definitely fine thread.

[Worth1]

Originally Posted by dmforcier

Okay, I don't get it. Why attach to the bottom plate at all? I guess I'll have to wait and see what you do.

Definitely fine thread.

The bottom plate gets squeezed to the top plate but the ways are in between.
This acts as a break to keep the carriage from moving.
It also will lock the other sliding piece to the top plate that I haven't made yet.
My other lathe has the same setup the stud is attached to the bottom plate.
This way you dont have to fiddle with two ends of a stud when you tighten just the top one.
I am just about out of Argon.

Worth

[Worth1]

I had a general contractor ask me once could you at least wait a little bit before hauling off scrap iron I had my eye on that stuff.
He asked me what I was going to do with it and I told him fabricating small projects.
Between the two of us we carried off all kinds of stuff.
Stuff most people wouldn't have the gumption to see something else in it other than trash or scraps.

Worth

[AlittleSalt]

Welcome to Texas

[Worth1]

I got up today ready to drill the holes, put the center drill in the chuck reached up to grab the chuck key and it was gone.
Looked everywhere for it twice or three times to no avail it was frigging gone.
The stupid drill press has a clip thing to put the key in and I can never seem to remember to put it there.
Even if it do it falls out and runs off.
So it ends up in the must unlikely places.
Out of desperation I decided to look in my, (it wont get lost here drawer) in the house.
There it was along with the rest of the stuff I didn't want to lose.
I have no recollection of putting that darn chuck key in that drawer.
Well today I did what I should have done a long time ago I tied it to the press with a string.
The one that goes to the metal lathe is going to get tied to that lathe too.
Chuck keys of all things have driven me nuts for years.
The one on my hole shooter is tied to the cord.
Well anyway I have the holes drilled and threaded the stud installed and it all fits like a glove.
I decided not to make a nut with a handle on it to tighten the thing I came up with something else.

Worth

[Worth1]

I think I have everything welded up and just waiting for it to cool down.
The part I am making now is the top slide that goes on the top part of the top part I made before.
Once this piece is cleaned up and fitted I will make the part that the tool rest goes into.
Right now it is square and clunky looking bout will be rounded off and ground.
Too busy to load pictures.


Worth